Hi Guys,I am new to this forum and have a few issues with flashing my PIC. I use the PICDEM2 PLUS DEV. board and i try to flash an PIC24F32KA302. Of course i have changed it to 3.3V by changing the linear controller.But I have several issues with that. At..
↧
PICDEM2 PLUS + PIC24F32KA302 (picccC_newbie)
↧
Windows does not recognize ICD 3 (hertnfab)
Hi I'm trying to install the driver for the MPLAB ICD 3 IN-Circuit Debugger. I followed the steps using the device manager to install the driver manually from it's location (C:\Program Files (x86)\Microchip\MPLABX\Switcher\64Bit\winusb\amd64). But Windows..
↧
↧
ICD3 Not Connecting/Programming for some reason. (acr)
Hello, For some reason today, my ICD3 decided to stop working on me and I can't program my chip. I'm using MPLABX v2.00, on Windows 7 Professional. I can see my ICD3 in the "debugger" field on the dashboard in the lower-left hand corner of the screen. I c..
↧
Null Post (kill me) (kcress)
I wish I could delete a post.. After having NO luck finding anything on IDC cable lengths once I posted my question the "similiar threads" covered my question just fine. Sigh...
↧
Anybody successfully using ICD3 and MPLABX in a VM? (Dave Nadler)
No joy here trying MPLABX/ICD3 in VirtualBox, though the TI JTAG tool for MSP430 works AOK as do other USB pass-through devices (this with Windows 7 32-bit as both guest and host OS).I have a customer that requires project delivery in a VM usable for ongo..
↧
↧
Q1:Can I connect picdem 2 plus to a pickit 3 with a pic18 MCU? Q2: ICD2 + win7 64 bit. (Sionking)
will it help if I will buy this : RJ-11 to ICSP Adapter Since my board don't have the apropiate connector ( I think it is an old version ), Can I just make one ? I can't wait a mouth till it will arrive I live in Israel and havn't found any store that sal..
↧
Debug mode is not working with my icd3 (ebedard)
PIC24FJ256GA106X16 compilerMPLABX 2.26ICD-3Programming in run mode is working. When trying to run in debug mode, the message below appears at the programming step:Failed to program device Configuration bits of my project:_CONFIG1( JTAGEN_OFF & GCP_OFF..
↧
ICD0104: Failed to initialize mediator Error in MPLAB IDE 8.85 (Digitalsystems)
Dear Sir,ICD0104: Failed to initialize mediator Error in MPLAB IDE 8.85 while selecting ICD2 programmer. When I am selecting Device PIC 16f1823 its working Properly with ICD2 but when I am selects Device as PIC16LF1518 then it gives error "ICD0104: Failed..
↧
ICD3 with AC244043/16F1825 I can't single step, even though breakpoints seem to work (DiBosco)
Folks, I have been debugging with an 16F1825 on the board and using the RJ11 connector to debug. It's been as successful as possible in that breakpoints and single stepping essentially worked. However, we needed the debug pins for the end product. So , I ..
↧
↧
MPlab 8 + ICD2 = Windows7 x64 problems (seedbarrett)
Hi everyone !I got troubles with ICD 2 on my new windows 7 x64. Before i was on a XP x86, there was no problems, but now i can't program my PICDEM 2 plus demoboard were I put a pic 2550. If you have some idea! In addition, if i use a an old who surely wor..
↧
ICD3 "The programmer could not be started: Failed to program the target device" (jlehman)
I am having a programming problem that is unique to a particular project. This is the dsPIC33E/PIC24E Bootloader. I get the following in MPLAB X in the ICD3 window: Connecting to MPLAB ICD 3...
Firmware Suite Version.....01.32.10
Firmware type............
↧
Debugging / watch Problem in MPLAB on CCS compiler (rolox)
HI,i have a similar problem that may have the same cause :I use CCS V5.036 with MPLAB 8 or MPLAB X (same result) and notice that some variable content is wrong (Arrays, Structs) in Watch window - but seem to be ok in programm !I did a small testprogramm a..
↧
ICD3 with PIC18F452 and MPLAB X version 2.26 (Jorgen)
Dear all, Please help. I get the following error message when I try to debug my software:"Could not connect to tool hardware: ICD3PlatformTool, com.microchip.mplab.mdbcore.ICD3Tool.ICD3DbgToolManager
The debugger could not be started. Terminating debug s..
↧
↧
Windows 7/32bit driver problems with MZ-SK and MX270BT_SK (Wavelength)
Gang, The built in ICD's for the new boards have a device ID of 0x8107. But the INF does not include that even on the latest release. So stupid Windows is taking over the device as a native HID device. If I edit the file and then super user put it back in..
↧
ICD3 in high impedance when not programming/debugging? (Szidor)
Hi! I have a circuit that uses the PGD/PGC pins as outputs. My worry is, that right after programming the firmware starts to run, and it will drive those pins as output and might cause problems if the ICD3 is still driving those pins. (I can disconnect wh..
↧
ICD3 "FPGA has failed its self test" (kcress)
Has there been a resolution or even an understanding of why MPLABX gets into the circular problem, "FPGA being reprogrammed - please wait - This may take a minute. Programming complete. Failed. Starting torture cycle again."? I can't find any responses to..
↧
Connection Troubles in MPLAB X for PIC16LF1829 (Leveatin)
I've been attempting to use an ICD3 device from Microchip to program a board hosting a PIC16LF1829. When attempting to connect to the device in MPLAB X IDE v2.30, the connection is very intermittent if present at all. The most common error message is "end..
↧
↧
ICD2 and Windows 8 problems (Dan Stroie)
Dear all, I got into trouble after my HDD broke and I had to replace it. On this occasion, I also decided to buy Windows 8 and installed it in my Sony Vaio laptop. I almost immediately found that this was a mistake, to migrate from Windows 7 to Wndows 8. ..
↧
Can't connect PIC18F24K22 to ICD3 (bix@jimbixby.com)
On a breadboard, I set up a simple circuit to connect ICD3 to a PIC18F2321. I can connect successfully and debug a simple program, so I know I have a working ICD3, and know it is properly wired to the 18F2321. I then replace the 18F2321 with an 18F24K22, ..
↧
ICD3 stopped working (Joe_Szabi)
I have been debugging my board (PIC18LF46K22,MPLABX v2.05 and XC8 1.33) and everything went well. Today it stopped programming. It displays Launching
Could n..
↧